Shenzhen / Hotel Key Card Manufacturing Factory
Room Card Chip Selection: Four Self-Checks to Pick by Model
Not sure which chip to use? In four steps, read the print on the card and the nameplate on the reader, then pick by model.
All four steps are done by you—look, copy, and photograph yourself; we do not read or test on your behalf.
- Self-check: read the old card print and reader nameplate, copy the model yourself
- Common frequencies: 125 kHz and 13.56 MHz
- Our boundary: we encapsulate blank chips by model; we do not read or test on your behalf
Low-Frequency & High-Frequency Chips
125 kHz and 13.56 MHz correspond to two reader systems; the frequency must match the reader, and cards are not interchangeable.
125 kHz
Low-Frequency ID Card
Recognizes a single card number; cannot store data or use sector encryption. Common in older hotels, legacy access control, and elevator cards.
Common models: EM4100 / EM4200 (read-only), T5577 (rewritable)
13.56 MHz
High-Frequency IC Card
Can store data and use sector encryption; the mainstream for hotel key cards. Phone NFC also uses this band.
Common models: Mifare Classic 1K (S50) / FM11RF08 / NTAG series / DESFire
Common Chip Comparison
All chips in the table can be encapsulated to the specified model. Which chip is inside the card does not mean it can open a particular lock.
We produce cards to the chip model you specify; the chip is encapsulated inside the card. Writing and encryption are completed by your lock provider or hotel.
| Chip Model | Frequency | Protocol | Capacity | Common Use |
|---|---|---|---|---|
| EM4100 / EM4200 | 125 kHz | Read-only ID | 64 bit card number | Legacy access, elevator cards, parking |
| T5577 | 125 kHz | Read/Write | 330 bit | Older systems needing changed card numbers; can emulate EM4100 |
| Mifare Classic 1K (S50) | 13.56 MHz | ISO/IEC 14443A | 1 KB (16 sectors) | Mainstream for hotel room cards |
| Mifare Classic 4K | 13.56 MHz | ISO/IEC 14443A | 4 KB | Multi-use cards needing more storage |
| FM11RF08 | 13.56 MHz | ISO/IEC 14443A | 1 KB | Domestic M1-compatible chip at lower cost |
| NTAG213 / 215 / 216 | 13.56 MHz | ISO/IEC 14443A / NFC | 144 / 504 / 888 B | Phone-readable; membership and interactive cards |
| DESFire EV2 / EV3 | 13.56 MHz | ISO/IEC 14443A | 2–8 KB | High-security, multi-application one-card systems |
| Dual-Frequency Composite Card | 125 kHz + 13.56 MHz | Dual protocol | By chip combination | Mixed old/new systems; one card for both readers |
Common uses: room access / membership / power pickup / one-card system
Four Ways to Identify the Chip Model
All four methods are done by the customer—look, copy, and photograph yourself. DONGKA does not read or test on your behalf; we only check the model against the table.
-
01
Read the print on the old card face (MIFARE / M1 / EM, etc.)
If the card prints MIFARE, M1, EM, etc., you can tell the band; if unprinted, check thickness—low-frequency cards have a thick coil, usually 0.9–1.1 mm. Look and copy yourself; no need to open the card.
-
02
Read the nameplate model on the lock or reader
Locks or readers usually carry a model nameplate; photograph it and match it to the table. Look and copy yourself; no need to open the card.
-
03
Send us clear photos of the old card front and back, or the reader nameplate, and we check the model against the table (model check only, no data reading)
DONGKA only does model matching and does not touch the data on the card.
-
04
Have your lock vendor confirm once more
What we compare with the table is "which chip this is," not "whether it can open your lock." For the final chip choice and how to write it, please confirm with your lock vendor. We produce cards to the chip model you specify; the chip is encapsulated inside the card. Writing and encryption are completed by your lock provider or hotel.
BOUNDARY
Boundary Between Card Making and Card Writing
DONGKA only supplies blank chips—no reading, no writing, no sector encryption. We produce cards to the chip model you specify; the chip is encapsulated inside the card. Writing and encryption are completed by your lock provider or hotel. We are responsible for the card's printing, size, encapsulation, and chip model; door-opening rights are the lock vendor's responsibility.
We do not promise a card will open any particular lock. Whatever chip the reader uses, we encapsulate to that model.
We only manufacture hotel key cards. We do not make door locks, nor provide smart-hotel or apartment systems, nor lock-system integration.
Chip-Related Questions
Who writes data to the chip inside the card?
We only produce cards and encapsulate blank chips; we neither read nor write data. We produce cards to the chip model you specify; the chip is encapsulated inside the card. Writing and encryption are completed by your lock provider or hotel.
I don't know which chip to use—can I order directly?
We recommend confirming the model first. Send clear photos of the old card front and back, or the reader nameplate model, and we check it against the table (model check only, no data reading). A mismatched model makes the card unusable.
When is a dual-frequency card needed?
Useful when some floors have new readers while old equipment is still in use. One card carries both 125 kHz and 13.56 MHz chips, so you need not stock a separate card per frequency; cost is higher than a single-frequency card.
Can NFC be embedded so guests open doors with a phone?
We can install NTAG-series chips that a phone can read. Whether a phone can actually open the door depends on the lock vendor's configuration, which is outside card manufacturing.
If my phone shows no response, is it not a high-frequency card?
A 13.56 MHz card responds when placed on a phone's NFC area; 125 kHz shows no response at all. Note: an encrypted M1 card may be unreadable by a phone, so no response does not mean it is not high-frequency.
Send your requirements; we quote after checking
Just provide the card type, quantity, chip model, and card artwork. If the model is unclear, send clear photos of the old card face or the reader nameplate.